How To Hide Screws In Wood In Just Minutes

Introduction

Finishing a woodworking project with visible may ruin the whole woodworking process or leave it to stay less aesthetically pleasing. How to hide screws in wood with time-saving solutions are always available.

No matter what your needs and your work status are, our recommendations will make the handiwork completely invisible with less time and effort. The sneakiest methods for hiding screws in wood are ready to be known.

How to hide screws in wood

When screwing down two separate pieces of wood, all the woodworker have ever experienced the terrible presenting of the visible screws. They are everywhere on new furniture or cabinets.

Screws must appear on the visible face of your stunning woodworking project. Hiding them will obviously take time during your design process. Once covered, the screws will no longer be your nightmare for a perfect woodworking look.

Here are our highly-recommended tips for covering ugly screws on wood. Apply our greatest methods of how to hide screws in wood to provide your new furniture and cabinets with a professional finish look instantly!

Place all the screws out of your sight

Perhaps this method is quite funny, but hiding the horrible screws is the most time-saving and simplest way. Simply locate them where they are not likely to be discovered. No need to well learn to use a screw digger!

Perfect location for covering the screws are the underside of your cabinet top or the tabletop, above or on the back side of your cabinet. Wanna know the amazing alternatives of how to hide cabinet screws? Keep reading!

Bury the ugly screws in counterbores

The counterbores can recess the screw heads under the workpiece’s surface. Just need to plug the counterbores for covering or highlighting the screw head. Purchase the plugs available in all common stores or make them yourself.

How-To-Hide-Screws-In-Wood

Use unique plugs for covering the screws

However, store-bought plugs are often cut from dowels with their end grain soaking in more stain compared with the face grain surrounding. Therefore, they don’t match your project stock’s tone. So, how to cover screws poking through magically?

If you prefer a visual detail with the awesome highlight for your woodworking finish, they will not be a bad selection. Choose the contrast colors if possible. For camouflaging a plug, cut your stuff from scrap material left from your project.

Utilize a plug cutter available in a drill press. This will surely deliver a picture-perfect match between the grain and wood tone as soon as your plugs are certainly glued and aligned. This is how to use wood plugs with ease!

Next, trim them with a chisel and then, a little-sanded flush. The buttons will stand perfectly on the wood’s surface as the fashionably decorative elements. This method may keep the painting over screws in wood away.

Wood Filler is an incredible choice

First thing first, removing the debris, flaky paint and sanding on the project’s surface and around the screws’ hole. Sanding the rough patches away by medium grit sandpaper in less than 100 grit. Learn to know well how to use a belt sander!

Remove the sanding and debris left
Remove the sanding and debris left

The debris and sanding removal

Clear all the remaining residue with a moistened cloth or a shop vac. Before using the moistened cloth, If you use a moistened cloth, make sure to keep the area dry. The screws must be slightly counterbored or screwed under the wood’s surface.

Make the filler mixture
Mix the wood fillers

Mix the wood fillers

Put a small dab and a ball-sized quantity of wood filler of the hardener on a small scrap wood piece or a hand palette. Mix two parts of fillers thoroughly with a puffy knife.

They will set faster for a wonderful and workable texture. For a couple of screws, less filler is enough. Make smaller batches available if necessary. Covering screws with wood filler will be well tackled with our specific steps.

Apply the prepared filler
Mix the wood filler

Mix the wood filler

Choose a puffy knife with its blade’s width no longer than 3.8 cm (1.5 inches) for maximizing your control. After that, spread a little filler over the hole, and the screw Remember to spread enough filler to make the hole flush with the wood surface.

Get the wood surface sanded
Sand the wood surface

Sand the wood surface

Next, sand the work surface once the filler was set. Let the spread filler set in 15 to 20 minutes. Smooth the work surface by the grit sandpaper. Remove all the irritating paint; debris left for a smoother surface of your handiwork.

Curl a part or section of wood

This is a quite easy-to-apply method for hiding screws in wood. Just need to curl away about 5 cm of the wood with a ready chisel. If needed, mark the exact location needed for driving your screws.

First, take a 14-mm-long chisel prepared. Locate it 1.5 cm away from the marking point with a bevel facing down. Next, get a thin strip of the wood curled up until you get the strip length of about 5 cm.

Drill the pilot holes

The next step is drilling a pilot hole for driving the screw after that. Attach your drill with a twist in the similar diameter to the screw shank. The hole should be under the curled strip. Drive the screws to get it flush enough with the wood surface.

Apply glue

Next, apply enough glue to both the project’s surface and the curled edge. Remember to use more glue in case the curled edge made splits or cracks when chiseling it. Never mind how to hide screws in MDF with this trick.

>>> Read more: How Long For Wood Glue To Dry

Avoid the sticking

Compress your curled edge to the wood surface. Wait for about an hour to let it dry. Place a scrap wood piece between two surfaces. If you don’t prefer the presence of a wood filler over screws, this would be a marvelous selection.

Utilize sandpaper for the project surface

Last but not least, sand the area with fine grit sandpaper. For dry and slightly tacky glue, wait for about 60 minutes. At that time, the dust and the glue will combine well to fill up any cracks and then, further hide your work surface.

Conclusion

Wood screws usually offer the powerful and speedy tricks to join all your project parts. After reading our useful pieces of information, you also know that they can be virtually invisible. How to hide screws in wood are also successfully provided.

In short, there are limitless unique ways for effectively covering the screw holes in woodworking. We do believe that our tips are well covered to allow the woodworkers to discreetly concealing any screw hole in any wood surface.