How To Burn Wood With Electricity – A Detailed Way To Follow

Introduction

Burning wood has become a crucial activity for those who need to decorate wood. The mark that is left on the wood after burning is definitely eye-catching and exquisite.

How To Burn Wood With Electricity

Usually, people will use fire to burn. But the biggest disadvantage of this method is that it is unsafe and uncontrollable. Electricity would be a good choice. However, you need to follow instructions strictly for the sake of your own safety. For that reason, in this article, I am going to show you how to burn wood with electricity safely and effectively.

How to burn wood with electricity (step-by-step guide)

To begin with, here are some basic things you should have: fan, brushes, electricity supply, wood, baking soda, glue and some additional stuff I will mention later.

Before finding out how to start, I have one important disclaimer for all of you. I am by all means, not responsible for any kind of damage you cause to yourselves or your properties. Using electricity, especially, high voltage electricity is dangerous. So make sure you are well-prepared because any careless can lead to accidents.

Step 1: Checking safety

Safety is one of the most important parts you should pay attention to. Apart from the danger of electricity, I also want you to pay attention when using sharp tools. It is very crucial to find out how to use tools, say, routers properly. Checking on Google how to round wood edges without router may be a good way to avoid possible injuries.

Step 2: Checking the power source

A power source is one of the most important things you will need to burn wood. I would suggest you use a high voltage power source. That is the main reason why safety should be your priority. Remember to pay attention to your safety by all means.

Step 3: Choosing the right type of wood

There are a thousand types of wood on the market. Plywood, whitewood, construction wood, softwood, hardwood and so much more. To ensure the process is taken place smoothly, you should choose the right type of wood that matches the voltage of the power source.

For those who may find it confused, I suggest you spend a few minutes searching for “what is whitewood?” or similar questions to pick up the right one. Different type of wood will lead to different looks.

How To Burn Wood With Electricity – A Detailed Way To Follow

From my experience, plywood is one of the best choices for wood burning. Using a belt sander on plywood would be a whole lot easier than when you choose other types. (And by thy way, remember to research the way to use a belt sander safely, safety first, remember?)

If your pieces of wood is a large one, then using a handsaw to divide it into small pieces is a good move. To save time as well as boost efficiency, remember to sharpen your handsaw before using.

Step 4: Increasing the efficiency of the process

What you are going to take away from my article is not just how to burn wood with electricity, you also learn how to burn it as effectively as it could be. The best way to do so is to reduce its resistance. Using extra substances such as water or baking soda may be a good idea.

Step 5: Setting it up

Once you have prepared it all, it is high time to get it all set up. Oh, and do not forget to brush your wood to make sure it all clean. Now connect the two leads of the transformers to both ends of the wood. Also, I suggest you use a fan to make it easier to see the circuit.

One of the most important things you should do is to make sure your pieces of wood is straight. There are various ways to do so, here is a source where you can use to find out how to unwarp wood.

Step 6: Plug it all in

Now let’s light them up. Plug in and you will see the electricity starts to burn your wood. It is up to you when to turn it off. I would always double check everything all over again to make sure everything is under my control. Being careful never causes any harm, isn’t it?

For those who are not familiar with all the electricity thing, you should ask somebody to show you how to do it. Under no circumstance should you try it without having a clear idea of what you are doing.

Step 7: Clean it up

If you have burned wood before, then I guess you are familiar with the messy pieces of wood when you have just finished. You should spend a few minutes to clean it to make it as beautiful as you expect. In case your purpose is to sell the piece of wood, it would be wise to how to unwarp wood and say, find some impressive ways to paint plywood if you can.

As far as I am concerned, this is one of the hardest parts that require a lot of attention. That is the reason why I told you to research how to burn wood with electricity with great details before starting.

After finishing burning, sometimes you want to link some pieces together. Well, I get that. Using wood glue is what people usually do if they do not have a large enough piece of wood. But you should notice how long for wood glue to dry as it may ruin your whole pieces of wood if you are careless in any step.

Woodworking is an interesting field. If you are new to the field, I think the best strategy is to check on some online products about woodworking industry before doing anything. Teds woodworking may be worth giving a shot. If you need more information, let’s check my teds woodworking review with the full detail.

Final thoughts

Contrary to what people thought, burning wood is not as hard as it seems, right? The first and foremost thing you have to pay attention to is your safety. From the power source, handsaw to a belt sander, it is very likely for you to get injuries from them. Getting high-quality tools and checking usage instruction before using is a must-do to all, even those who are familiar with burning wood.

Below are everything I know about how to burn wood with electricity. Feel free to contact me if you have something to ask. See you next time!